The Manuals are in.pdf format If you are using Windows, press 'Control F' after the manual has loaded. This will produce a search box in the upper right corner of the screen for easy searching. KT8900 User Manual (pdf) Dual Band 5-2015 KT8900R User Manual (pdf) Tri Band 1-2016 240-260MHz added. The new Dual Band handheld radio INTEK KT-980HP is the new High Power version of the well known model KT-960 PLUS (UV-5R). The main difference and feature of model KT-980HP is the new transmitter circuit design which is equipped with a RENESAS RQA0011DNS Silicon N-Channel RF power MOSFET semiconductor, rated at 10,47W.
2016-11-24Creating a programming cable for a QYT KT-8900 with some soldering4 years ago
But, the QYT KT-8900 has a different programming interface, just a 3.5 millimeter plug with ground, rx and tx data. So I found a very good resource for chinese radios which has the answers: 3 PIN Programming Cable for a BTech, QYT, etc Mobile which has the right pinout. I just cut the Baofeng cable to get at the gnd, rx and tx wires. Com: qyt kt-8900d dual band vhf uhf mini color. KT-8900 / JT-6188 User Manual The Manuals are in.pdf format If you are using Windows, press 'Control F' after the manual has loaded. This will produce a search box in the upper right corner of the screen for easy searching. KT8900 User Manual (pdf) Dual Band 5-2015 KT8900R User Manual (pdf.
QYT KT-8900 radio with homebrewed interface cable, CC-BY-SA
Qyt Kt 7900d User Manual Pdf Download
I bought a cheap 2m/70cm mobile/base radio, a QYT KT-8900 which has thespecial feature of being very small but still able of putting out 25 Watton the 2 meter VHF band and 20 Watt on the 70 centimeter UHF band.The display looks a lot like my Wouxun KG-UVD1P, complete with batterystatus indicator which is not much use when the radio has a constant 13.8Vfeed. The menus are quite similar, so this is probably nota coincidence.I bought it via aliexpressand it got shipped at a reasonable speed to my house. In the original listingwas mention of a programming cable, but it showed up without one. I asked the seller about this and directly a baofeng programming cablewas shipped to me.But, the QYT KT-8900 has a different programming interface, just a 3.5millimeter plug with ground, rx and tx data. So I found a very goodresource for chinese radios which has the answers: 3 PIN Programming Cable for a BTech, QYT, etc Mobile which has the right pinout.I just cut the Baofeng cable to get at the gnd, rx and tx wires.Next I had to wait for a cable with the right 3.5mm connector to show up.The connector in the back is sunk into the case and the 3.5mm connectorsI had in the junkbox did not fit. But a broken PC speaker set wanted todonate a cable with 3.5mm connectors that were slim enough. Next tryingthe result with chirp radio programming softwareunder Linux. And suddenly I could copy a list of channels I had and uploadit to the radio in 5 minutes, which is a lot faster than manual programmingwhere getting more than one channel programmed in correctly under 5 minutes is hard,see for example Programming Repeaters into the QYT KT8900 Mini Dual Band Mobile Radio Review - AF5DN - Youtube.At the moment the cable looks very experimental. Now it has been tested Iwill use tiewraps and heatshrink tube to make it sturdier and make itlook a lot better.As a radio it's ok, but not ideal. I was testing with meetnetwerk baretta - hobbyscoopand the antenna on the roof for 2 meter and 70 centimeterand noticed I had pulsing audio of the output frequency of PI2NOS on theBaretta frequency. Pulsing audio is a known problem in this radio, see KT8900 FAQ at miklor.combut I have no channels with receive CTCSS.
